We have been cleaning drains in Phoenix, San Diego and the Inland Empire for over two decades. The most common drain clogs are kitchen sinks and main drain sewer stoppages, we have seen it all, and can take care of any clog you have. Most people don’t know there are several ways to clean a drain. Some homeowners will rent a drain snake in not knowing that we will clean your drain and provide you with a warranty for around the same cost!
When you wash up before bed or take a nice, hot shower before heading off to work in the morning, it is your plumbing system that you are relying on. The same is true when you run your dishwasher or laundry machine. To say that your plumbing system plays a major role throughout the day, every day, in your home is to make a massive understatement. That is why it is so vital that you are able to use your plumbing system reliably, which in turn means that you must hire professional plumbers that you can count on to do the job right, such as those on our fine staff.
Schuler Service has been providing quality solutions for your plumbing, boiler, and electrical systems since 1923. When you call us for help, you will always be put right through to our helpful staff—even during the weekend and holidays. We feature 24-hour emergency plumbing services because we know the unexpected can happen. When it does, make your first thought Schuler Service!
M and M, Heating & Cooling, Plumbing & Electrical offers swift, reliable plumbing and rooter services throughout Longmont, CO & surrounding areas. Our fully licensed and insured team of qualified plumbing professionals ensure efficient, dependable, and long-term performance from your plumbing system.  From water heater installation and repair, to drain cleaning and clog removal, there is no challenge we can’t resolve to your complete satisfaction.  Providing convenient and prompt scheduling, accurate diagnosis of any plumbing-related difficulties, and tidy job sites, we alleviate stress, mess, and aggravation, and deliver rewarding results.
Over the past 10+ years, we’ve become one of the most trusted Phoenix plumbing companies in the Valley. We’ve built up this trust by adhering to a high level of excellence and working to complete every job the right way on the first visit out. Knowing that a job is done correctly the first time gives our customers a peace of mind, and it is an approach that has helped solidify our customers’ sense of trust in us.
Cast iron and ductile iron pipe was long a lower-cost alternative to copper, before the advent of durable plastic materials but special non-conductive fittings must be used where transitions are to be made to other metallic pipes, except for terminal fittings, in order to avoid corrosion owing to electrochemical reactions between dissimilar metals (see galvanic cell).[17]

Pipe is available in rigid "joints", which come in various lengths depending on the material. Tubing, in particular copper, comes in rigid hard tempered "joints" or soft tempered (annealed) rolls. PeX and CPVC tubing also comes in rigid "joints" or flexible rolls. The temper of the copper, that is whether it is a rigid "joint" or flexible roll, does not affect the sizing.[19]
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
“We had a toilet emergency one morning. After unsuccessful plunging efforts, we called Intelligent Service – and within 20 minutes, they were at our house. They found that the sewer line from our house to the street had snapped. Within 2 hours they had a permit and a backhoe in our front yard, and started work. By 5:00pm, we had water! They were extremely sympathetic to our situation. They were careful not to track snow and mud into the house. They cleaned up the area both inside and outside. Have already recommended the company to the many neighbors.”
Most typical single family home systems won't require supply piping larger than 3⁄4 inch (19 mm) due to expense as well as steel piping's tendency to become obstructed from internal rusting and mineral deposits forming on the inside of the pipe over time once the internal galvanizing zinc coating has degraded. In potable water distribution service, galvanized steel pipe has a service life of about 30 to 50 years, although it is not uncommon for it to be less in geographic areas with corrosive water contaminants.
Called in on Wednesday evening to schedule a new sink hookup and was put on the schedule for Friday morning with no problems. Ryan arrived and took a look at what I had, gave some recommendations and provided a couple quotes. He took his time and made sure everything he installed was the most efficient and correct for my setup. We will continue to use and strongly recommend Atomic Plumbing.
Those who attempted to bring plumbing indoors faced technical as well as attitudinal challenges. Decisions on how wastewater was removed required as much concern as those made to ensure an adequate water supply. But equally vexing was the prevailing miasma theory of disease, which held that illnesses stemmed from "bad air" that was readily identifiable by its offensive odor. This led to a distrust of early indoor plumbing that tended to leak and a deadly fear of the sewer gas that accompanied the leaks. It is no wonder then that many individuals maintained a strong belief that elimination was best taken care of out of doors.
While it’s their job to make sure your pipes work like a well-oiled machine, it’s not their job to rebuild the wall they had to demolish to make that happen. So, while you’re going to get that water problem fixed, you’ll want to discuss in detail what kind of “mess” they might leave behind prior to the start of the project so you can plan accordingly. Remember, there are some jobs you can do yourself. Here’s how to solder copper pipe joints!
An apprenticeship is the most common pathway to becoming a plumber. Many unions and businesses mandate that an apprentice receive a minimum of 246 hours of technical education, which could include instruction in math, applied physics and chemistry, and up to 2,000 hours of paid, practical training working with an experienced plumber. Safety training is also an important component of the process, since injuries are common in this line of work. "We have many hours worth of [Occupational Safety and Health Administration] training before we go on to a job site," says Patrick Kellett, the administrative assistant to the general president for the United Association of Journeymen and Apprentices of the Plumbing, Pipe Fitting Industry of the United States, Canada and Australia. "We're very conscious of the dangers that come with working in construction."

It does help in regards to procedures and rules in order to better understand your options.  Obviously cost is always an issue and the size of the company probably determine the labor cost.  That is why some times people take chances with "others' hoping that there have good experience but because they are independent operators there pricing might be more flexible.
A company may charge approximately $1,000 to replace a 50-gallon tank-style electric water heater (not including any upgrades required by building codes). Replacing a gas-powered water heater might cost $1,100 (not including code upgrades). Some companies roll the disposal of an old heater into the overall cost of the new water heater installation. Other professionals charge an additional removal fee that can range from $35 to $150.
PBT – flexible (usually gray or black) plastic pipe which is attached to barbed fittings and secured in place with a copper crimp ring. The primary manufacturer of PBT tubing and fittings was driven into bankruptcy by a class-action lawsuit over failures of this system.[citation needed] However, PB and PBT tubing has since returned to the market and codes, typically first for "exposed locations" such as risers.
Called at 2pm and had service completed by 6pm on a cold any busy day with lots of frozen pipes. Extremely fast and took the time to communicate both the issue, and associated costs of repair. Also very communicative for when someone would be by. Got an update call from the service center saying “we are a bit busy but you are still in the schedule for today”. Much appreciated so I could plan my afternoon while waiting. Highly recommended.

plumbing, piping systems inside buildings for water supply and sewage. The Romans had a highly developed plumbing system; water was brought to Rome by aqueducts and distributed to homes in lead pipes—hence the name plumbing from the Latin word plumbum for lead. During the Middle Ages, however, plumbing became almost nonexistent. In fact, London's first water system after the Middle Ages (c.1515) consisted partly of the rehabilitated Roman system; the rest was patterned after it. Modern plumbing began in the early 1800s, when steam engines became capable of supplying water under pressure and cheap cast iron pipes could be supplied to carry it. The common materials used today in water supply pipes are steel, copper, brass, plastic, and lead. Plumbing for sewage is made of cast iron, steel, asbestos cement, copper, and plastic. Water pressure is usually insufficient to supply the needs of tall apartment and office buildings; in such cases storage tanks are installed on the roof, into which a pump lifts water. The water then flows through the piping system of the building by gravity. Smaller buildings may have a pneumatic tank for the same purpose. The tank is partly filled with air, which is compressed when water is pumped in so that it will force water through the pipes. Sewage and drain systems typically have a trap, often a loop-shaped section of pipe, to seal off vapors in the pipes from the rest of the building. Vent pipes lead these vapors to the outside of the building; they also eliminate any suction in the piping and thus prevent the siphoning of water from traps when a nearby fixture discharges. In the 1970s and 80s flexible polybutylene plumbing was widely installed in standard and mobile homes. When unprecedented numbers of these plastic pipes began leaking because of exposure to chlorine and other chemicals in tap water, homeowners brought class-action lawsuits against the manufacturers, which were settled in 1995 for hundreds of millions of dollars.
Most plumbers, pipefitters, and steamfitters learn their trade through a 4- or 5-year apprenticeship. Apprentices typically receive 2,000 hours of paid on-the-job training, as well as some classroom instruction, each year. In the classroom, apprentices learn safety, local plumbing codes and regulations, and blueprint reading. They also study mathematics, applied physics, and chemistry. Apprenticeship programs are offered by unions and businesses. Although most workers enter apprenticeships directly, some start out as helpers. The Home Builders Institute offers a pre-apprenticeship training program in plumbing and other trades.
At Magnolia Plumbing, Heating & Cooling, we offer 24/7 emergency plumbing services for all of our clients in the Washington, DC area. But is your plumbing issue urgent enough to call us? If you’re asking this question, the answer is most likely a yes. We can get to your home quickly and restore your plumbing system so that you continue to have access to potable water, or so that your home is protected from a burst pipe or a smaller leak.
Whatever your preference and price point, there’s a tub to sooth. That’s, of course, if you want a bathtub. Many homeowners — particularly those who don’t have young children living with them — have thrown the tub out with the bath water in favor of installing a walk-in shower. Just make sure to consider the pros and cons of tub to shower conversions.

PVC/CPVC – rigid plastic pipes similar to PVC drain pipes but with thicker walls to deal with municipal water pressure, introduced around 1970. PVC stands for polyvinyl chloride, and it has become a common replacement for metal piping. PVC should be used only for cold water, or for venting. CPVC can be used for hot and cold potable water supply. Connections are made with primers and solvent cements as required by code.[22]
Our mission is to give something back to the community in appreciation for the community's support of our business. Whether it’s through Atlanta’s Professional sports team, High and Middle Schools, local sports teams or home town events, we love coming out and enjoying and supporting the communities that have helped make us the company that we are. 
I needed a neutral place to research plumbing jobs: had the suspicion I was being 'led down a garden path' because I knew nothing - other than how expensive it was and how urgent  'do it NOW!" it was. I appreciate the cost estimate and national average pages which confirmed my suspicions.  I found another plumber through this site and hope for better, less panic, less cost service from now on. Thanks.
Using corrosive chemicals to dissolve a clog is like throwing a grenade down a gopher hole. Instead, Wroblewski recommends flushing your drains weekly with a half cup of baking soda and one cup of vinegar. Let it fizz in the drain for ten minutes, then pour in four cups of boiling water. Find out about the plumbing nightmares that will make you cringe.
Do you think you have a water leak in your house or business in Phoenix, San Diego and the Inland Empire? Does your floor feel hot? Have you noticed an unexpected increase in your Phoenix, San Diego and the Inland Empire water or gas bill? Our plumbers in Phoenix, San Diego and the Inland Empire are experts in the latest electronic leak detection technology.

Do you need a Hot Water Circulating Pump for your home in Phoenix, San Diego and the Inland Empire? This system can deliver hot water to fixtures quickly without waiting for the water to get hot. Rather than relying on low water pressure common in most water lines, recirculating systems use a pump to rapidly move water from a water heater to the fixtures.
Both public and domestic toilet design is becoming increasingly technologically driven, with automatic flushes and sensor-controlled washing-and-drying facilities becoming commonplace. In parallel, environmental sustainability requirements to save water have resulted in a range of dual-flush cisterns, waterless urinals, and human-waste recycling innovations. High levels of toilet provision in every home, along with highly developed sewerage systems, are no longer necessarily seen as signs of progress and economic development. Such assumptions are now being questioned. Many parts of the world are not economically or environmentally in a position to build modern, expensive water and sewerage systems: It is not a high priority. Water is becoming an increasingly expensive and scarce resource; some see it as “the new oil” in terms of future geopolitical tensions. Far from being a sign of economic development, many see the emphasis upon water-based sewerage systems and flushing toilets as old fashioned, colonial, and unsustainable. Instead, new, more sustainable solutions are being developed, especially within prosperous advanced Asian countries that can afford such research. Such systems will incorporate the most modern technological and scientific advances in the fields of engineering, pathogen control, and urban governance (Chun 2002; Mara 2006).
With a reputation for outstanding work, At Your Service Plumbing Company is a Denver plumbing company providing services to Arvada, Aurora, Boulder, Broomfield, Centennial, Columbine, Commerce City, Denver, Edgewater, Englewood, Federal Heights, Firestone, Frederick, Golden, Gunbarrel, Highlands Ranch, Ken Caryl, Lakeside, Lakewood, Littleton, Longmont, Louisville, Northglenn, Sherrelwood, Thornton, Welby, Westminster and Wheat Ridge. Learn more about our service guarantee

Alphabet City, Battery Park City, Bowery, Carnegie Hill, Chelsea, Chinatown, Cooperative Village, East Village, Greenwich Village, Harlem, Hell's Kitchen, Inwood, Kips Bay, Koreatown, Lenox Hill, Lincoln Square, Little Germany, Little Italy, Lower East Side, Madison Square, Manhattan Valley, Marble Hill, Morningside Heights, NoHo, NoLita, NoMad, Peter Cooper Village, Rose Hill, SoHo, TriBeCa, Tudor City, Two Bridges, Upper East Side, Upper West Side, Washington Heights
While it’s their job to make sure your pipes work like a well-oiled machine, it’s not their job to rebuild the wall they had to demolish to make that happen. So, while you’re going to get that water problem fixed, you’ll want to discuss in detail what kind of “mess” they might leave behind prior to the start of the project so you can plan accordingly. Remember, there are some jobs you can do yourself. Here’s how to solder copper pipe joints!
Water systems of ancient times relied on gravity for the supply of water, using pipes or channels usually made of clay, lead, bamboo, wood, or stone. Hollowed wooden logs wrapped in steel banding were used for plumbing pipes, particularly water mains. Logs were used for water distribution in England close to 500 years ago. US cities began using hollowed logs in the late 1700s through the 1800s. Today, most plumbing supply pipe is made out of steel, copper, and plastic; most waste (also known as "soil")[21] out of steel, copper, plastic, and cast iron.[21]
×