I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
The movement of liquids and gases through pipes is critical to modern life. In homes, water is needed for both drinking and sanitation. In factories, chemicals are moved to aid in product manufacturing. In power plants, steam is moved to drive turbines that generate electricity. Plumbers, pipefitters, and steamfitters install and repair these pipe systems.
Are you 100% satisfied with the quality of the water in your home? It doesn’t matter if you use a private well or if you get your water from the municipal supply. There is no guarantee that your water is going to be of the high quality that you both deserve and demand. That is where our water treatment system professionals come in. When you hire us, we can test your water to determine precisely what’s gone wrong. We can then install the exact type of water treatment system that you need to get the most out of your water supply.

The straight sections of plumbing systems are called "pipes" or "tubes". A pipe is typically formed via casting or welding, whereas a tube is made through extrusion. Pipe normally has thicker walls and may be threaded or welded, while tubing is thinner-walled and requires special joining techniques such as brazing, compression fitting, crimping, or for plastics, solvent welding. These joining techniques are discussed in more detail in the piping and plumbing fittings article.
Pipe is available in rigid "joints", which come in various lengths depending on the material. Tubing, in particular copper, comes in rigid hard tempered "joints" or soft tempered (annealed) rolls. PeX and CPVC tubing also comes in rigid "joints" or flexible rolls. The temper of the copper, that is whether it is a rigid "joint" or flexible roll, does not affect the sizing.[19]

Your water heater is an essential part of your home, heating water for showers, dishwashing, laundry and more. On average, a traditional water heater will last 8-12 years. The general consensus is that it’s better to replace your water heater with a new one than to repair one that’s 10 years old or more. Older models are less energy-efficient and thus more costly to run than newer models with better technology. Here are some indicators of when it may be time to replace an old water heater instead of repairing it:


Help! The toilet won’t stop running. It’s a bummer, sure, but it’s something you don’t need to call your plumber about. In fact, DIYers should take note that it’s a quick fix that will cost you just $5. For instance, your handle might just be sticking, which can be solved by spraying some lubricant where the handle meets the porcelain. Ready to DIY? Here’s how to fix a running toilet.
When something goes wrong with your plumbing system, speed is essential. The faster you address the problem, the better off you and your wallet will be. Water can quickly cause thousands of dollars in damage. Leaks can soak floors, ceilings and foundations, causing rot and mold that may make your home uninhabitable. Get a direct quote from a professional plumber.  Continue Reading
Need Help?  Have a question or comment?1-888-827-4223Email UsGet Exclusive Offers & Expert TipsJOINTerms of UsePrivacy PolicyInterest Based AdsFor U.S. Residents Only © 2018 Ace Hardware. Ace Hardware and the Ace Hardware logo are registered trademarks of Ace Hardware Corporation. All rights reserved. For screen reader problems with this website, please call 1-888-827-4223 or email [email protected]
Roto-Rooter plumbers in Lakewood provide full service plumbing maintenance and repairs and clogged drain cleaning, 24 hours a day, including toilet repairs. Roto-Rooters Lakewood plumbers offer residential and commercial plumbing services that customers depend on for all of their local plumbing needs. Trusted and recommended since 1935, Roto-Rooter is the premier provider of plumbing and drain cleaning services in Lakewood, CO. Homeowners and businesses depend on Roto-Rooter 24 hours a day, 7 days a week. Our specialty is emergency services. We stand by our estimates and guarantee our work. Your call will be answered by a trained customer service representative who will handle your request quickly and schedule service at your convenience.
Don’t flush floss, tampons, or even so-called “flushable” wipes. They don’t break down like toilet paper does and can come back to haunt you later. “Toilets are more water-efficient now than they were 20 years ago, so there sometimes isn’t enough volume in the flush to force debris down,” says Marcin Wroblewski, president of ExpressRooter Plumbing in Toronto. “An object will get lodged in the trap and cause blockage when waste builds up days later.”
The thicknesses of the water pipe and tube walls can vary. Pipe wall thickness is denoted by various schedules or for large bore polyethylene pipe in the UK by the Standard Dimension Ratio (SDR), defined as the ratio of the pipe diameter to its wall thickness. Pipe wall thickness increases with schedule, and is available in schedules 20, 40, 80, and higher in special cases. The schedule is largely determined by the operating pressure of the system, with higher pressures commanding greater thickness. Copper tubing is available in four wall thicknesses: type DWV (thinnest wall; only allowed as drain pipe per UPC), type 'M' (thin; typically only allowed as drain pipe by IPC code), type 'L' (thicker, standard duty for water lines and water service), and type 'K' (thickest, typically used underground between the main and the meter). Because piping and tubing are commodities, having a greater wall thickness implies higher initial cost. Thicker walled pipe generally implies greater durability and higher pressure tolerances.
Hi, I'm Brian Wear, owner of Brian Wear Plumbing. I started my own plumbing company in 2005, but I have been a plumber in the Columbia, Missouri area for over 20 years. Being a plumber for that length of a time requires a passion for plumbing repair and tireless hours perfecting the practice. We are a fully licensed business that will work to ensure that all your plumbing needs are met. I pride myself on our personal, friendly plumbing services at a reasonable price. When you call, we'll make sure you get the best service possible. I look forward to meeting you and providing for all your plumbing needs.
Specialized plumbing tools include pipe wrenches, flaring pliers, pipe vise, pipe bending machine, pipe cutter, dies, and joining tools such as soldering torches and crimp tools. New tools have been developed to help plumbers fix problems more efficiently. For example, plumbers use video cameras for inspections of hidden leaks or problems, they use hydro jets, and high pressure hydraulic pumps connected to steel cables for trench-less sewer line replacement.
Our Water Heater failed and flooded our attic on the weekend. They answered the phone and had someone out the same day. By the next day, we had a new water heater installed and hot water, all over the weekend. They were quick and professional. Justin D answered all my questions and took the time to explain. When speaking to Justin it was clear that he cared and was well trained in customer experience. Thank you all for making a stressful situation a little easier to deal with. We appreciate your services.
Ryan and Zach came quickly to my residence when the office scheduled them to come a day early to my pleasant surprise. They sharply dressed and very professional. They quickly diagnosed the kitchen faucet problem, brought the right tools to affect repairs and fixed the leak, I was impressed by their professionalism and teamwork. If I ever have another plumbing problem, Ryan and Zach performance convinced my to call Atomic next time.

PBT – flexible (usually gray or black) plastic pipe which is attached to barbed fittings and secured in place with a copper crimp ring. The primary manufacturer of PBT tubing and fittings was driven into bankruptcy by a class-action lawsuit over failures of this system.[citation needed] However, PB and PBT tubing has since returned to the market and codes, typically first for "exposed locations" such as risers.
Lutz Plumbing, Inc. is a 4th generation family-owned business, with roots going back to 1920. Our company was founded by William Lutz, grandfather and great grandfather of current owners Jim Lutz and Amber Lutz Sewell. 2015 was one of our biggest years on record, with unprecedented sales and the growth of our workforce. When you hire the plumbers on our staff, you are guaranteed to work with skilled professionals that take their work and their company seriously.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?

Rooter Plumbing

×