Don’t fix it if it’s not broken, right? While the saying makes sense, when it comes to plumbing, it’s best to simply keep an eye on things. This means not overlooking toilets, sink drains, pipes and valves. And, it’s a good idea to schedule an annual maintenance appointment with your plumber, so you don’t have to pay a ton of money later! Got a leak? Here’s how to fix a water-shutoff valve that’s leaking.
Nationally, the average water heater repair cost ranges between $120 and $200, although prices can range up to $400 or more. Water heater repair costs will depend on the type of water heater you have (tankless, electric, natural gas, etc.), the source of the problem, the cost for new parts, and labor rates in your area. Common water heater issues include problems with the thermocouple, thermostat, heating element and leaks. Most standard electric water heaters have two thermostats and two elements. One example for the cost to replace a bad thermostat is $185 for parts and labor. Replacing both the thermostat and the heating element could cost approximately $150-$200. The thermocouple is a safety device that senses when the pilot light is burning and signals the gas valve to close if the pilot light goes out. If your thermocouple is bad or corroded, the average cost to clean and repair it could be between $350 and $400. If your water heater has started to leak, it is usually more cost-effective to invest in a new water heater than to repair it, unless you’re covered by a warranty.
Sometimes, homeowners are not sure whether they should call a local plumber immediately or wait a while longer for repairs. But remember that no matter how small the problem is, it can escalate into something much worse as time goes on. We recommended contacting our team immediately when you notice any performance issues with your system, including leaking or clogs, so that we can get out there ASAP. You can also schedule an appointment with us to add on important plumbing features, like a water softener or an automatic shut off valve.
Plumbing—from fixtures to vent pipes—in high-rise buildings and skyscrapers duplicated that used in other structures, but with the addition of several unique features. As gravity-fed city mains generally lift water no more than five or six stories, electrically operated pumps raise it to elevated storage tanks beyond that point. Water levels in the tanks are maintained automatically. Water is supplied from them throughout the structure by gravity, air pressure, or booster pumps. Likewise, gravity removes waste water by way of drainage pipes.
Justin and Paul were extremely polite. They worked as quickly as they could and got my hot water heater replaced. I have two dogs that are a handful, and they learned their names and talked to them to help keep them calm, which meant a lot to me. I felt comfortable having them in my home. The customer service at the company was great as well, very helpful on the phone. I would recommend them.
I just had my pipe under the sink unclogged and new pipes put in $600.00, then they flushed out the pipe from under the sink to the outside pipe $700.00, Total of $1.600.00, I thought that the price was high, I got the plumber from Home Advisors, not sure they had to do all they did but they said I needed the work done. The same evening hike using the dishwasher I had a leak in one of the pipes they put in, they came back the next day to fix it. Don't know if I will use them again.. They were K&D kitchens.
Faucets for the kitchen come in an array of styles, and costs vary as well, from simple single handle models running less than $50 to pull down faucets like those used in restaurant kitchens costing more than $200. One handle or two, separate pullout sprayer or pull down, countertop or wall mount, these also feature a variety of finishes from stainless steel to nickel and bronze.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?