We had a Saturday evening before Easter emergency when our water heater began leaking. We got the water turned off and contacted Atomic Plumbing. Their friendly appointment person told us they would have someone here the next morning, Easter! Jim came at 11 am and told us it would be best to replace it. We told him to go ahead. They went out and got a high quality one as we requested and installed it in a few hours. Very professional and kept us informed along the way. We appreciate Atomic Plumbing.
Do you need a bathroom faucet in Phoenix, San Diego and the Inland Empire? Do you need a kitchen faucet repair in Phoenix, San Diego and the Inland Empire? A dependable faucet repair in Phoenix, San Diego and the Inland Empire use to be hard to find. Not anymore. An Option One plumber in Phoenix, San Diego and the Inland Empire is your local expert in all types of bathroom or sink faucet repairs and faucet installation in Phoenix, San Diego and the Inland Empire.
CON'T FROM COMMENTS EARLIER. However, the installation took less than 3/4/ hour and was a basic regulator with no other function. Looking up the price afterwards, invoice did not list type or price, it appears that it would have cost me around $60 for the regulator and another $15 or so for the additional supplies necessary to install it and it was really a rather simple job with easy access. Given that, it seems that $300 for less that an hours worth of on site work, company says it does not include commute time in its prices, is a little high. While flat rate quotes are nice, they must take into consideration situations where the work load differs depending on the circumstances. Therefore, unless you are at the upper end of the harder work needed than the average job. it can be argued that my estimated price of $300 for labor was more than a little high. Maybe I am wrong since I have not used their services for years and am not knowledgeable of the costs of equipment and professional labor today.
At Wayne’s Plumbing Repair, we proudly serve Charlotte, Matthews, Mint Hill, Indian Trail, Pineville, and Weddington, North Carolina with professional plumbing services. We can replace fixtures, install pressure-reducing valves (PRVs), repair water lines, or even install plumbing in a newly built home. Our friendly and knowledgeable technicians are even available for emergency service 24 hours a day. Our top-notch plumbing services include: Water Heater Repair, Toilet Repair, Garbage Disposal Repair, Faucet Repair, Pipe Repair.
You’ll know when it’s time to install a new water heater. Water heater installation costs average between $360 and $780 nationally, with rates increasing depending on the project. The total project cost will be higher when you include the cost of the heater itself. Select your new water heater based on the number of occupants in your home and the number of gallons of capacity you’ll need. Installation costs can vary based on the type of water heater you are removing and the type you are installing, any necessary repairs, regional cost of labor, and whether disposal of the old heater is included. Natural gas water heaters retail on average between $650 and $900 for standard models. Electric water heaters range between $300 and $700 for standard models. Tankless electric water heaters retail on average between $250 and $700 for standard models. Tankless gas water heaters retail on average between $200 and $1,300.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
Apprentice plumber: Apprenticeship programs generally provide the most comprehensive training for novice plumbers. Either union locals and their affiliated companies or nonunion contractor organizations can administer this training. Apprenticeships typically consist of at least three to four years of paid, on-the-job training and some hours of related classroom instruction.