Beginning in the 1950s plastic pipe, most notably that made of polyvinyl chloride, has been used in ever increasing amounts. In the following decades, other plastics were introduced into pipe manufacture. However, by the last years of the century a number of plastic-pipe failures had occurred. Problems were attributed to defective manufacture and, in some cases, a chemical reaction taking place between the material used to make the pipe and chlorine in the water that it carried. These events led to class action lawsuits and a general reevaluation of the use of this inexpensive and easily worked alternative piping material.
Plumbing repairs and maintenance should be taken seriously. Homeowners can avoid costly and dangerous plumbing issues with help from Mr. Rooter Plumbing. Our professionals have all the experience to diagnose problems and keep your plumbing system in great shape. Give us a call at (855) 982-2028, or request a job estimate for professional plumbing repair service.

The straight sections of plumbing systems are called "pipes" or "tubes". A pipe is typically formed via casting or welding, whereas a tube is made through extrusion. Pipe normally has thicker walls and may be threaded or welded, while tubing is thinner-walled and requires special joining techniques such as brazing, compression fitting, crimping, or for plastics, solvent welding. These joining techniques are discussed in more detail in the piping and plumbing fittings article.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
Hello I had a plumber do an estimate for me to replace our copper pipes with plastic as we have no existing walls up in our basement yet...pretty basic job... so we figured we could upgrade as we do live in Northern Ontario and it does tend to get quite cold here in the winters.  We dont have any existing problems with our plumbing right now just figured it would be good time to do the job and perhaps change the pipes to 3 quarter inch for faster flow.  Well I never thought in all my life I would get an estimate back that would state $350.00 an hour in labor...yes that is correct $350.00 an hour...estimated 10 hours for the job to be completed.  So he quoted me $3500.00 for labor alone.. not supplies?  Well needless to say I will be happy with my half inch copper pipes and will happily wait for my bathtub to fill up at a slower pace.  Just wanted to know what your thoughts are on this $350.00 an hour quote?  Thank you and enjoy your day.
I needed a neutral place to research plumbing jobs: had the suspicion I was being 'led down a garden path' because I knew nothing - other than how expensive it was and how urgent  'do it NOW!" it was. I appreciate the cost estimate and national average pages which confirmed my suspicions.  I found another plumber through this site and hope for better, less panic, less cost service from now on. Thanks.

At Magnolia Plumbing, Heating & Cooling, we offer 24/7 emergency plumbing services for all of our clients in the Washington, DC area. But is your plumbing issue urgent enough to call us? If you’re asking this question, the answer is most likely a yes. We can get to your home quickly and restore your plumbing system so that you continue to have access to potable water, or so that your home is protected from a burst pipe or a smaller leak.
Lutz Plumbing, Inc. is a 4th generation family-owned business, with roots going back to 1920. Our company was founded by William Lutz, grandfather and great grandfather of current owners Jim Lutz and Amber Lutz Sewell. 2015 was one of our biggest years on record, with unprecedented sales and the growth of our workforce. When you hire the plumbers on our staff, you are guaranteed to work with skilled professionals that take their work and their company seriously.
The straight sections of plumbing systems are called "pipes" or "tubes". A pipe is typically formed via casting or welding, whereas a tube is made through extrusion. Pipe normally has thicker walls and may be threaded or welded, while tubing is thinner-walled and requires special joining techniques such as brazing, compression fitting, crimping, or for plastics, solvent welding. These joining techniques are discussed in more detail in the piping and plumbing fittings article.
As important as it is that you are able to distribute potable water throughout your home in a dependable manner, it would be a much less convenient state of affairs if you were not also able to dispose of that water just as conveniently, not to mention hygienically. That is why we suggest allowing our Master Plumbers to complete any and all drain and sewer services that you may require. From basic cleanings to complex repairs and eventual replacements, we truly do it all. If you have any reason to suspect a problem with your drain and sewer system, give us a call right away.

Galvanized steel potable water supply and distribution pipes are commonly found with nominal pipe sizes from 3⁄8 inch (9.5 mm) to 2 inches (51 mm). It is rarely used today for new construction residential plumbing. Steel pipe has National Pipe Thread (NPT) standard tapered male threads, which connect with female tapered threads on elbows, tees, couplers, valves, and other fittings. Galvanized steel (often known simply as "galv" or "iron" in the plumbing trade) is relatively expensive, and difficult to work with due to weight and requirement of a pipe threader. It remains in common use for repair of existing "galv" systems and to satisfy building code non-combustibility requirements typically found in hotels, apartment buildings and other commercial applications. It is also extremely durable and resistant to mechanical abuse. Black lacquered steel pipe is the most widely used pipe material for fire sprinklers and natural gas.
After completing an apprenticeship program, plumbers, pipefitters, and steamfitters are considered to be journey workers, qualifying them to perform duties on their own. Plumbers with several years of plumbing experience may earn master status by passing an exam. Some states require a business to employ a master plumber in order to obtain a plumbing contractor’s license.
Our professional staff of qualified plumbers are highly familiar with New York City's unique plumbing structure, and we are here to provide each of our customers with the most professional and affordable plumbing service for any residential or commercial plumbing problems. Whether you are located in Manhattan, Queens, Bronx, Brooklyn, Staten Island or Westchester County - We are here 24/7 to handle any of your plumbing needs.
We had a Saturday evening before Easter emergency when our water heater began leaking. We got the water turned off and contacted Atomic Plumbing. Their friendly appointment person told us they would have someone here the next morning, Easter! Jim came at 11 am and told us it would be best to replace it. We told him to go ahead. They went out and got a high quality one as we requested and installed it in a few hours. Very professional and kept us informed along the way. We appreciate Atomic Plumbing.
For many centuries, lead was the favoured material for water pipes, because its malleability made it practical to work into the desired shape. (Such use was so common that the word "plumbing" derives from plumbum, the Latin word for lead.) This was a source of lead-related health problems in the years before the health hazards of ingesting lead were fully understood; among these were stillbirths and high rates of infant mortality. Lead water pipes were still widely used in the early 20th century, and remain in many households. In addition, lead-tin alloy solder was commonly used to join copper pipes, but modern practice uses tin-antimony alloy solder instead, in order to eliminate lead hazards.[13]
×